Panzhihua Adiprene Duracast S800 PUR-ester/MDI material report,
The tensile strength of non-strong PBT is 50MPa, and the tensile strength of glass additive PBT is 170MPa. 1. PC/ABS alloy ABS plastic currently on the market has good surface hardness and gloss, but it is used in LED TV frames, digital product housings, etc., in terms of gloss, brightness, surface hardness, scratch resistance and abrasion resistance. Sex and other aspects are slightly insufficient. Experiments show that the effect of toughener on PA6 tough material is different at room temperature and low temperature. Ascendas Engineering Plastics PBT modified engineering plastics 1. High-gloss and innovative surface-shining technology Star-Shining gives the ink cartridge holder the appearance quality. A technological innovation has achieved the balance of product surface quality, mechanical strength and other aspects.
1. Used in the electrical industry, used in the aerospace, aviation, electronics, instrumentation, computer and other industries as the insulating layer of power and signal lines, corrosion-resistant and wear-resistant materials can be used to make films, tube sheet rods, bearings, washers, valves and Chemical pipelines, pipe fittings, equipment container linings, etc. [4]
Polytetrafluoroethylene bottle[6] 2. Used in electrical, chemical, aviation, machinery and other fields instead of quartz glassware, used in atomic energy, medicine, semiconductor and other industries for ultra-pure chemical analysis and storage of various acids, alkalis, and organic solvents. It can be made into high-insulating electrical parts, high-frequency wire and cable sheathing, corrosion-resistant chemical utensils, high-cold oil pipelines, labor, etc. It can be used as additives for plastics, rubber, coatings, inks, lubricants, greases, etc. [4]
3. This product is resistant to high temperature and corrosion, has excellent electrical insulation, aging resistance, low water absorption, and excellent self-lubricating performance. It is a general-purpose lubricating powder suitable for various media and can be quickly applied to form a dry film , To be used as a substitute for graphite, molybdenum and other inorganic lubricants. Suitable for thermoplastic and thermosetting polymer release agent, excellent load-bearing capacity. It is widely used in elastomer and rubber industry and anti-corrosion. [4]
4. Used as a filler for epoxy resin to improve the wear resistance, heat resistance and corrosion resistance of epoxy adhesives. [4]
5. Mainly used as a binder and filler for powder cakes. [4]
To
To
Panzhihua Adiprene Duracast S800 PUR-ester/MDI material report,
This feature makes graphite an abrasion resistance additive used in many applications placed in water, such as water paving shells, vanes and seals. 4. Polysiloxane Polysiloxane is a migratory wear resistance additive When added to thermoplastics, the additive will migrate to the surface of the part and form a thin film. In the context of environmental protection, energy conservation and environmental protection are deeply rooted in the hearts of the people. How to adjust the room temperature to a suitable temperature in a short time and maintain this temperature at a cost has become a more painful issue for everyone. Thin-walled products can be injection molded. Dimensionality: The connection size tolerance requirements of the intake manifold and the engine are very strict, and the installation of the sensors and actuators on the manifold must be very accurate.
To
1. Stable under normal temperature and pressure, avoid humidity, heat and high temperature [4]
There is no real melting point, and it decomposes slowly above 450℃ and becomes a gas directly. At 327°C, the mechanical strength suddenly disappeared. Insoluble in any solvents. In addition to reacting with molten alkali metals, it is not corroded by any substance, even if it is boiled in hydrofluoric acid, aqua regia or fuming sulfuric acid, sodium hydroxide, it will not change. [4]
2. White, odorless, tasteless, non-toxic powder, commonly known as “Plastic King”. It has excellent chemical stability, corrosion resistance, airtightness, high lubrication, non-stickiness, electrical insulation and good anti-aging resistance. High temperature resistance, the working temperature can reach 250℃. It is resistant to low temperatures and has good mechanical toughness at low temperatures. Even if the temperature drops to -196°C, it can maintain 5% elongation. Corrosion resistant, inert to most chemicals and solvents, resistant to strong acids and alkalis, water and various organic solvents. Good weather resistance and the best aging life among plastics. High lubrication is the lowest friction coefficient among solid materials. Non-adhesive is the one with the smallest surface tension among solid materials and does not adhere to any substance. It is non-toxic, physiologically inert, and has no adverse reactions as artificial blood vessels and organs implanted in the body for a long time. [4]
resolve resolution
To
Through the analysis of the above different synthetic heat-resistant ABS copolymer samples, it is understood that due to the strong nylon PA6 itself, the process is about 80% longer than similar materials-and does not lose mechanical properties. Since the glass fiber is oriented along the flow direction during injection molding, the mechanical properties and shrinkage rate are strong in the orientation direction, and the product is deformed and warped. Therefore, when the mold is designed, the position and shape of the gate should be reasonable, and the mold can be exposed in the process. After removing the caries product, put it in hot water and let it cool down. Generally, the gloss of fine strong particles is more uniform, and the injection speed is generally fast to prevent premature solidification during injection.
The moisture content of ABS raw materials should be controlled below 013%. However, in crystalline plastics, the deflection temperature under load is the temperature between the glass transition point and the melting point of the crystal. Therefore, it is a meaningless temperature both theoretically and practically, and the deviation of the measurement results is also obvious. The surface coating of the tough nylon fiber-reinforced material coated with the tough nylon surface treatment agent can smoothly pass through 100 grids and boiling in water. 1. When the blending ratio of PC/ABS with different characteristics is >50%, ABS will form a squint phase. PC becomes the dispersed phase. The modified nylon raw material nylon resin is in the same vein as nylon fabrics. Our clothes are not poisonous, so the possibility of this material is gone.
To
